Hi Phil, Video is called "Auto Login on Mobile Devices" .
Link is: .

Cheers,
rick

@phildunlap
Hi Phil, Yes, that's the video I referred to.

Cheers,

rick

I have a cloud connection v3.6.0. I connect to Mango es v3.6.4. If I try to setup a phone app to connect directly to the Mango es as per the video instructions, it does not work. shows proxy error 401.
Also having no luck setting up user to connect directly to graphic in user setup.

Help!

Cheers,

Rick

I have a Mango version 3.5.6 It is connected to a DDC board thru Bacnet I/P.. There are several DDC boards on this system. When I save the datasource and send out Whois I can see them all. When I recheck the next day, most of the DDC boards and their points are no longer there? If I re save the datasource, then all of the DDC boards and their points show up again.. I have only 10 points saved as data points.

Ideas?

Cheers,

Rick

I get the same refused to connect messafe using the IP address

Hi Phil,

1. yes this is the pc at the IP address you saw
   2.yes this is where the cloud connect server, I believe. I had Joel set it up.
   3.yes the change to the password was for this instance on Mango
2. Joel set it up, but I see Mango as a service on this pc

I get a refuse to connect message

Hey Phil, Just a refuse to connect message?

@rowen

Sorry to seem so helpless but I'm at a loss?

R

Hi Phil, I went to that link to reset password. Not sure how to stop Mango. Joel installed the cloud connect for me. I found a "mango" in services on my pc and I stopped it. When I go to Mango to get into h2-web part I get the following

Hi Craig, Yes when I restart my pc and go to localhost:8090, without running the ma-start.bat, I get the Mango login screen. Yes, I am running ma-start.bat as administrator.

Hey Joel, Yes I get the Mango login screen when I go to localhost or IP plus :8090

So I restart my pc. I try to run ma-start.bat but it comes up with the error from above. (port in use) I go to our domain name provided through mangoautomation.net and it opens and auto fills in my user info. This doesn't work, just says login failed bad credentials.
All other passwords do not work either. I ran netstat to check ports and it says that port 8090 is not in use. I checked that the env.properties show to use port 8090. Where else can I look?

Cheers,
R

yes. I have started and stopped pc several times. Just get as the picture above

I believe my problem could be that the ma-start.bat file won't run. Here is the error message that I get.

CHeers,

Rick

Hi Jared
Mango is 3.5 ES3702 and cloud connect I bought in Feb this year. Not sure where to find version?
I added new user to server, then logged out of server.
I didn't change the old password but it now doesn't work.
Where are proxy settings?

I have a mango v3.5 I am using a cloud connect to talk to the mango.
Today I added a new user. When I logged out and tried to log back in with the new user it did not work? Also the old password now doesn't work? Also I see ma-start.bat doesn't open now. As you can guess from this I have very limited understanding of the system. Any ideas?

Cheers,
Rick

@pikey4 Hey! Sorry I didn't reply sooner but your info helped me out. Thx.

R

Hi! I have amps and volts (3 phase) that I'm reading. I want to calculate kWh. I assume the easiest method would be to setup a meta data point but I'm a novice. any thoughts? I will also want to move this data to a chart and gauge.

Cheers,

Rick

Hi Phil, So I changed the port 8090 and after a restart all is running again. Thanks!!

Cheers,
Rick