Please Note This forum exists for community support for the Mango product family and the Radix IoT Platform. Although Radix IoT employees participate in this forum from time to time, there is no guarantee of a response to anything posted here, nor can Radix IoT, LLC guarantee the accuracy of any information expressed or conveyed. Specific project questions from customers with active support contracts are asked to send requests to support@radixiot.com.
A Bit Stuck on Writing Multiple MODBUS Registers
-
-
Interestingly, when I write the hex values I get this pop up error..
Nothing written in the log during this time however :/
-
@dan
just curious why the 'Number of registers' is '0'? shouldn't be at least '1'? -
It's greyed out and disabled.
-
Hi Dan
Regarding the address, I think you are correct. Well since other address work you are correct. If 4104 is not working I would try 4103.
I think @MattFox is correct regarding the ones's compliment that needs to be written to address 9. I get a different number tho.
-
I think your answer is right here craig, something is amiss with how I did it, but looking at it now, I think we're all starting to break the back of it.
-
Hey Guys, thanks again for helping out. That's a big number. I'll give that one a go, I'll try it into 4104 and 4103.
Cheers
Dan -
Interestingly I get a timeout message if I try writing the whole decimal number to either data point register.
If I change back to a hex value it just comes up with the top blue error again.
-
although might actually currently be a timeout in the network, as it's on the top of a mountain in NZ. at the end of a Mimomax link :/
I do believe it's snowing up there currently.. -
Bugga, still same timeout message when network is responding better.
com.serotonin.modbus4j.exception.ModbusTransportException: java.net.SocketTimeoutException: connect timed out
If I interrogate a standard read point it works fine.
-
although might actually currently be a timeout in the network, as it's on the top of a mountain in NZ. at the end of a Mimomax link :/
I do believe it's snowing up there currently..@dan Sounds like I need to make a roadtrip! Haha
-
With a bloody big hammer.
-
Seems like perfect troubleshooting conditions :)
ye so basically no response from the command. Only thing I can suggest is checking if the actual number is causing the "no response" by sending a different digit. is the modbus request going over the network or do you have a local mango instance there ? -
Yeh the Mango instance is a few hundred ms away. It seems to work fine reading in voltages and RPM's and the like. Just been playing up a little today probably due to the weather.
Even when it was working fine the write function still didn't seem to be the correct syntax. -
If I was troubleshooting I would create data points instead of using the modbus tool. It looks like you are using quite an old version of mango and I have had issues with the modbus tool in older versions. I think it would be worth cancelling that out of the troubleshooting.
-
OK, thanks Craig. I have a data point I made earlier which I will go back to and see what it does.
Thanks -
So I emailed DSE from their website contact form for shits and giggles, not really expecting to hear back... A nice fella from the UK emailed back almost immediately with all the official docs on the thing. I thought that was awesome.. Anyway, here's a more explanatory version of what I had found originally...
So looking at that, I should be sending 35702 to 4104 and 29833 to 4105
:)
I'll give that a go.. -
I may be wrong here but I am pretty sure that the only way that mango will write them in the same command is if you use 1 x 4-byte data point.
-
ok sweet as, thanks for that I'll give it a go
-
You should capture the command with Wireshark and see if it matches what you are expecting.
