Hi Philips,
The MANGO ES upgraded every time there is upgrade available , I didn't take action to backup any older version unless the ES has a auto backup "If yes - do tell me how to restore"
The scan result on earlier post was performed on MANGO PC (free version) - that we have 3.5 and 3.6.
Can you elaborate in details steps how shall we rescue MANGO ES now
My main concern is MANGO ES.
regards,
Frank
Dear Philips,
Can we have or how should we do if we want to have "one , zero , relinquish" ? As following, example.
If cannot be done, how about - the relinquish name change the name only to "Auto" ?
regards,
Frank
Dear Philips,
Thank you, since there are confuse matter on verifying the issue we face. Can we downgrade the bacnet module version to 3.5.2 for further checking on MANGO ES ? Please advise .
We will redo check on both version, and come out with the schematic diagram for better understanding for both of us.
As I told you earlier - we noticed some controller unable to discover on bacnet version 3.6.0
Thank you
regards,
Frank
Dear Philips,
Apologize for late reply.
I cannot send the wire shark file capture in this forum, I will drop an email to you with same subject as above for the file capture that test scan on bacnet version 3.5.2 and 3.6.0 on MANGO installed on PC.
Hope this can ease you to troubleshoot, same issue happen in MANGO ES on scanning bacnet mstp and ip.
Regards,
Frank
Dear Philips,
We will re-test again with wireshark and post the result here.
regards,
Frank
Hi Philips,
Regards to question 2 on relinquisher, how can I come to the page you shown me ? I wish to know how you did that.
I only manage to go to dashboard designer by adding "setpoint value" , as below-:
.
Regards to question 1 on priority array, what I snap shot is from another software where we can see a BO priority thru a template by the software. I will try it out, if any further clarification require I will resend in this post.
Thank you.
Frank
As we would focus on MANGO ES, I believe my technical post will in this group only.
I have 2 questions
Q1) I only know we can command the write priority in data points for binary output (active / inactive) , can we view the template for priority array? For example as below.
Q2) If I use write priority : 8 , the MANGO ES binary ouput will point to priority 8, others priority from 9 to 16 will unable to function, as the BO we allow to set either "active" or " inactive" mode only. There is no NULL allow
Please advise.
Regards,
Frank
As for testing, we have ES and also a PC installed with MANGO (non-commercial version).
With bacnet module version 3.5.2 on MANGO PC (Windows 10), we manage to scan ALL the controllers on old interface screen on bacnet/IP discovery.
Upon we upgrade the bacnet module version 3.6.0 on MANGO PC, even the old interface or new interface we faced similiar issue that we did not manage to get all the DDC controller online in the list on bacnet/IP.
Initially, we won't perform above test scan until we noticed MANGO ES bacnet discovery had very less of controllers it manage to scan on bacnet/IP on version 3.6.0.
Same issue we encounter too on bacnet/mstp on MANGO ES - manage to discover Alerton and Honeywell Spyder but not others brand of bacnet mstp ddc on same rs-485 comm. Is there any restriction on brands bacnet ms/tp ddc that MANGO ES allow to discover on bacnet ms/tp ?
Any firewall or settings we need to look into ?
regards,
Frank
Dear all,
May anyone of you advise me the reputable and reliable brand of wireless temperature sensor that you all use to interface with MANGO ?
I have an inquiry to monitor the temperature for a wine fridges. I would like to install a small system that monitor numbers of wine fridges temperature. When temperature reach above certain level, a sms message to notify client.
regards,
Frank