Hi Phil,

This is a part of my log file in Hex (extract from MANGO/logs/SerialIO-1.log)
2016/06/20-07:58:57,479 I 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

that correspond to:
01030000;01040000;01050000;01060000;01070310;01110000;01120000;01020000;01200002;01210007;01240000;01449233;03010001;03028192;03036403;03041028;03050000;03060000;03070000;03080000;03090000;01260000;01300062;01323938;01090000;99130001;01600013;01284000;00000000;00000000

Message terminator is: 0x0a
Every value has the format: aaaa bbbb;
aaaa = ID point
bbbb = value point

In total, I have 30 values to visualize, but I'm not be able to do this.

Thanks

Thanks for your previous response, but I am not be able again to visualize results of data received by serial port.
I changed the format of data, but I don't resolve the trouble.

I explain my situation in the better way I can to do.
I have a PLC that send a string of value in the following format:

aaaabbbb;ccccdddd;eeeeffff;...etc

aaaa,cccc,eeee are the Point ID (ex 0103, 0107,0106)
bbbb,dddd,ffff are values to display

(If necessary, I don't have any problem to insert a char terminator or use a time delay from one transmission and other)

Serial port has the following parameters
9600 8N1 and no has any flow control, it's a USB to DB9 converter.

Data from PLC to PC, flow correctly (I have verified with a Serial sniffer)

MANGO Data point configuration:
Bit Rate: 9600
Flow control in: None
Flow control out: None
Data bits: 8
Stop bits: 1
Parity: None
Read Timeout: 100ms

Log I/O in serial data source is correct (I read data in Hex format in SerialIO-1.log file)

I think the problem is in Regex parameters, but I don't know where.
What's correct sintax of these fields?
Have you any ideas on other possible troubles?

Thank you again
Paolo

Hi,
I have some trouble with "Serial Data Source".
I have a simple data receive from COM port with the following format:

Byte 1, 2 data point identificator
Byte 3, 4 Value of Data point

Data is trasmitted by other device on COM port to MANGO at random time.

DATA SOURCE is configured as follow:
Read Timeout (ms): 1000
Use terminator?: NO
Message regex: ([0-9]{2})(.*)
Point identifier group: 1
Configuration is in hex: YES
Maximum size of message: 1000

DATA POINT is configured as follow:
Data type: Numeric
Point identifier: 1
Value group: 2
Value regex: .*

An example of data trasmitted by the device is: 00 01 03 02 (HEX)
00 01 = data point 1
03 02 = value 770 (dec)

In no way, I can to show the value of data in WATCH LIST (n/a).
Where is the mistake?
Thanks
Paolo