• Recent
    • Tags
    • Popular
    • Register
    • Login
    1. Home
    2. patd2020

    Please Note This forum exists for community support for the Mango product family and the Radix IoT Platform. Although Radix IoT employees participate in this forum from time to time, there is no guarantee of a response to anything posted here, nor can Radix IoT, LLC guarantee the accuracy of any information expressed or conveyed. Specific project questions from customers with active support contracts are asked to send requests to support@radixiot.com.

    Radix IoT Website Mango 3 Documentation Website Mango 4 Documentation Website Mango 5 Documentation Website
    P
    • Profile
    • Following 0
    • Followers 0
    • Topics 3
    • Posts 12
    • Best 0
    • Controversial 0
    • Groups 0

    patd2020

    @patd2020

    0
    Reputation
    832
    Profile views
    12
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    patd2020 Unfollow Follow

    Latest posts made by patd2020

    • RE: How To set up email alert level sensor

      thank you Jeremy. Great clear instructions. most appreciated

      posted in How-To
      P
      patd2020
    • How To set up email alert level sensor

      Hi Guys I have a ultarsonic level sensor set up in mango with MODBUS the dat point is set up well and is reading fine. But I cannot seem to find how to create an email alert, say for example if the water level exceeded 4m, how to get an email sent to somebody? similarly if it went under a level.?

      thanks in advance

      posted in How-To
      P
      patd2020
    • RE: GPIO Controller command protocol

      Thanks ,v8dave and Phil for your responses. Here is the document. Also to tell you about the device it is fully web accessible and has setup pages including a socket setting where you can configure
      Network Parameters setting(TCPB),
      Port ID
      Server address
      TCB Time out setting

      0_1467854211947_GPIO control protocol V1.8.pdf

      posted in How-To
      P
      patd2020
    • GPIO Controller command protocol

      Hi there, I have a WiFi/Ethernet relay board (8 channels output) 3 channel input. The input is monitoring a door status using a reed switch. (open or closed status) how can I in mango have a data point for monitoring the open closed status. the relay board ships with a GPIO Controller protocol manual but is is over my head. I can post it here if it helps,

      posted in How-To
      P
      patd2020
    • RE: Modbus data source setup

      Sorry I meant to say I change the data source to MODBUS IP because I could not get the COM to to work

      posted in User help
      P
      patd2020
    • RE: Modbus data source setup

      Here is an update. I now can read the registers of both devices. the second device which had Modbsus ASCII as default I had to change to RTU. Now I need to figure out how to set up the data points

      posted in User help
      P
      patd2020
    • RE: Modbus data source setup

      here is the RS485 Modbus guide for the Flow m0_1466480777062_FlowRS485.doc

      posted in User help
      P
      patd2020
    • RE: Modbus data source setup

      Thanks Joel & Phil. yes I see your point about the non matching slave/com port. I should have matched it to avoid confusion but that is actually how they are setup/ Slave 1 on Com2 and slave2 on COM1. Yes I am on Windows. I will attempt to run your suggested tests and report back

      posted in User help
      P
      patd2020
    • RE: Modbus data source setup

      any recommendations
      for this type of software?

      posted in User help
      P
      patd2020
    • RE: Modbus data source setup

      Thanks for your suggestion Joel but still getting the no response error

      posted in User help
      P
      patd2020