How do I enable I/O logging?

Also, does the "point value may not be reliable" have anything to do with it?

Jonathan

This is a pic of what Im experiencing. And its only 2 points (OD outlet and discharge temp). The other 13pts work fine.

I dunno if this helps or not.

Jonathan

Attachment: download link

Hi all,

Have a new and exciting problem with M2M2 with regards to continuity of data.

Ive got a 5 devices in a daisy chain. Controller->Power Peter->3x I/O Modules to Rs485/LAN gateway that M2M2 polls from. This should work just fine. The unit beside it doesnt have a problem.

Now, the problem seems to be data collisions. my sampling intervals are 5 seconds and at the end of every other interval a non-zero value (lets say discharge temperatures) just cuts down to zero and then picks up to the "proper" value after the next 5 seconds.

The baudrates of the devices are all 19200, everything is setup properly as far as I can tell.

I dont understand why this is different than the time I did this before...any ideas?

Thanks,

Jonathan

Hi all,

Have a new and exciting problem with M2M2 with regards to continuity of data.

Ive got a 5 devices in a daisy chain. Controller->Power Peter->3x I/O Modules to Rs485/LAN gateway that M2M2 polls from. This should work just fine. The unit beside it doesnt have a problem.

Now, the problem seems to be data collisions. my sampling intervals are 5 seconds and at the end of every other interval a non-zero value (lets say discharge temperatures) just cuts down to zero and then picks up to the "proper" value after the next 5 seconds.

The baudrates of the devices are all 19200, everything is setup properly as far as I can tell.

I dont understand why this is different than the time I did this before...any ideas?

Thanks,

Jonathan

Please do. That would be awesome.

Thanks,

Jonathan

NVM. played around with it and figured it out. all is well.

Now, how do I make it so that when I download mangos watchlist data that it doesnt make 3 VERY long columns where the different data points are joined end-to-end (the timestamps repeat beginning of data point 1- to - end of data point 1 joined to beginning of data point 2 - to - end of data point 2).

What Im looking to do is to have the date/time in the first column and each data point have its own column. Also, I have no need for the "annotated" data column, how can I get that to go away?

Finally, I would also like to control the file download destination at the end of the day. Ie: download to a destination in a Mango File on a server or something rather than it going into my downloads folder on my laptop.

Thanks,

Jonathan

if #.0 specifies 1 decimal place, then does #.x where x is 0,1,2,3,4 etc etc specify 1,2,3,4 decimal places, respectively?

Thanks,

Jonathan

Hi all,

In my graphical view I have various temperatures and pressures etc around a heat pump cycle. Now Mango seems to want to give me about 5 useless decimal places (theyre all zeroes)...I want to chop it to 1 or 2 decimal places.

How?

Jonathan

Hi all,

In my graphical view I have various temperatures and pressures etc around a heat pump cycle. Now Mango seems to want to give me about 5 useless decimal places (theyre all zeroes)...I want to chop it to 1 or 2 decimal places.

How?

Jonathan

Hi,

I was wondering if it was at all possible to have Mango change the format of the watchlist charts when you download the file.

1. My current setup has all the data logging in 3 continuous columns of data with the timestamps for the different points being joined end to end. I would like to have each attribute being displayed in its own column.

2. Also, can I control what directory/destination folder Mango sends the downloaded watchlist data for the day?

Are there settings for this? Any help would be VERY appreciated.

Thanks,

Jonathan

Hi,

I was wondering if it was at all possible to have Mango change the format of the watchlist charts when you download the file.

1. My current setup has all the data logging in 3 continuous columns of data with the timestamps for the different points being joined end to end. I would like to have each attribute being displayed in its own column.

2. Also, can I control what directory/destination folder Mango sends the downloaded watchlist data for the day?

Are there settings for this? Any help would be VERY appreciated.

Thanks,

Jonathan

Im currently trying to do something similar with a Tstat5e. Isquared software is loaded on there and things are ok. Problem is just polling the registers in Mango. It works in CATNET, but not with Mango...its very confusing.

Any suggestions? Anyone?

Hi all,

Were a long time user of CATNET and are switching over to Mango and its going relatively smooth. But I was wondering how to make a settable point that acts like an on-off switch for a device.

I would also like to make an interface screen where I can see my system and have the switches as little buttons on the screen. See the picture for what Im looking to make. In this particular setup, you can turn on the fan by clicking on it. I want to do something similar with Mango.

Any help?

Thanks,

Jonathan

Attachment: download link

Hi all,

Were a long time user of CATNET and are switching over to Mango and its going relatively smooth. But I was wondering how to make a settable point that acts like an on-off switch for a device.

I would also like to make an interface screen where I can see my system and have the switches as little buttons on the screen. See the picture for what Im looking to make. In this particular setup, you can turn on the fan by clicking on it. I want to do something similar with Mango.

Any help?

Thanks,

Jonathan

No success. Same error.

chrome

Hi,

I recently downloaded the mango meta module and am trying to configure meta points to do calculations for me.

The programming seems fairly simple. Im no expert, but Im not having many problems yet.

I configured a meta point to do a basic multiplication operation and I have hit a couple problems.

1. When I try to edit or enable a created meta point...I get the error in "error for meta" png file.
2. When I try to save a created meta point...I get the error in "attempting the save" png file.

Any help?

Thanks,

Jonathan

Attachment: download link

Hi,

I recently downloaded the mango meta module and am trying to configure meta points to do calculations for me.

The programming seems fairly simple. Im no expert, but Im not having many problems yet.

I configured a meta point to do a basic multiplication operation and I have hit a couple problems.

1. When I try to edit or enable a created meta point...I get the error in "error for meta" png file.
2. When I try to save a created meta point...I get the error in "attempting the save" png file.

Any help?

Thanks,

Jonathan

What are the default units of Station Pressure?

Im getting 12.2...12.2 whats? kPa? millibar? what?

Thanks

NVM. it works. I jumped the gun.